污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
深圳市嘉士達精密儀器有限公司
深圳市嘉士達精密儀器有限公司
閱讀：396發布時間：2023-2-17
序號 量規類型 量規名稱 標準圖號
1 E26燈頭 通規 7006-27D-3
2 E26燈頭 止規 7006-29L-4
3 E26燈頭 接觸性能規（美規） 7006-29-3
4 E26燈頭 接觸性能規（日規） 7006-29-3
5 E26燈頭 防意外接觸規 (防觸電) 7006-29A-2E26燈頭通規 7006-27D-3
Purpose目的：
To check the maximum dimensions of the screw thread and dimension T1 minimum of caps on finished lamps.
檢查成品燈燈頭螺紋zui大尺寸和T1的小值
Testing 測試方法：
When the cap on a finished lamp has been screwed into the gauge as far as it will go, the center contact shall be co-planar with, or project beyond, surface X.
當成品燈上的燈頭wan全旋入量規內時，燈頭中心觸點應與X面共面或凸出X面。
E26燈頭止規 7006-29L-4
Purpose目的：
To check the minimum outside (major) diameter of the screw thread.
檢查成品燈燈頭螺紋小外徑.
Testing 測試方法：
When the gauge is placed over the thread of the cap on a finished lamp, held cap uppermost, the center contact shall not project beyond surface “X”. Only the weight of the gauge itself shall be used in the test.
當量規套在成品燈的燈頭螺紋上時，燈頭中心觸點不應凸出量規的X面，見嚴禁利用量規的自身重量進行。
E26燈頭接觸性能規 7006-29-3
Purpose目的：
To check lamp dimensions for contact making in IEC holders.
檢驗燈在燈座中有關接觸性能的尺寸。
Testing 測試方法：
The shape of the lamp with regard to the fit in the lampholder is assured to be correct. If the lamp can be pushed into the gauge till plane W reaches plane V or project beyond it.
如果燈插入量規時，W面可與應V面共面或凸出V面，則可認為燈的形狀與燈座的配合是合格的。
For E26/24 capped lamps, when surfaces V and W are coincident, the of the cap including any solder or conductive material, shall not extend above surface X.
對于E26/24燈頭的燈，當V面與W面共面時，燈頭頂部的焊錫或任何導電部分不能升出X面。
E26燈頭防意外接觸規 (防觸電) 7006-29A-2
Purpose目的：
To check protection against accidental contact during insertion of caps E26d on finished lamps.
檢驗成品燈上E27燈頭在插入時防止意外接觸性能。
Testing 測試方法：
The shape of the lamp with regard to protection against accidental contact is assumed to be correct if, when the lamp is pushed as far as possible into the gauge, surface W does not protrude beyond surface V.
如果燈頭wan全插入量規時，W面沒有凸出V面，則可認為燈的防意外接觸性能是合格的。
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼